; ; RTP Configuration ; [general] ; ; RTP start and RTP end configure start and end addresses ; ; Defaults are rtpstart=5000 and rtpend=31000 ; rtpstart=10000 rtpend=20000 ; ; Whether to enable or disable UDP checksums on RTP traffic ; ;rtpchecksums=no ; ; The amount of time a DTMF digit with no 'end' marker should be ; allowed to continue (in 'samples', 1/8000 of a second) ; ;dtmftimeout=3000 ; rtcpinterval = 5000 ; Milliseconds between rtcp reports ;(min 500, max 60000, default 5000) ; ; Enable strict RTP protection. This will drop RTP packets that do not come ; from the recoginized source of the RTP stream. Strict RTP qualifies RTP ; packet stream sources before accepting them upon initial connection and ; when the connection is renegotiated (e.g., transfers and direct media). ; Initial connection and renegotiation starts a learning mode to qualify ; stream source addresses. Once Asterisk has recognized a stream it will ; allow other streams to qualify and replace the current stream for 5 ; seconds after starting learning mode. Once learning mode completes the ; current stream is locked in and cannot change until the next ; renegotiation. ; Valid options are "no" to disable strictrtp, "yes" to enable strictrtp, ; and "seqno", which does the same thing as strictrtp=yes, but only checks ; to make sure the sequence number is correct rather than checking the time ; interval as well. ; This option is enabled by default. ; strictrtp=yes ; ; Number of packets containing consecutive sequence values needed ; to change the RTP source socket address. This option only comes ; into play while using strictrtp=yes. Consider changing this value ; if rtp packets are dropped from one or both ends after a call is ; connected. This option is set to 4 by default. ; probation=8 ; ; Whether to enable or disable ICE support. This option is enabled by default. ; icesupport=false ; ; Hostname or address for the STUN server used when determining the external ; IP address and port an RTP session can be reached at. The port number is ; optional. If omitted the default value of 3478 will be used. This option is ; disabled by default. ; ; e.g. stundaddr=mystun.server.com:3478 ; ; stunaddr= ; ; Some multihomed servers have IP interfaces that cannot reach the STUN ; server specified by stunaddr. Blacklist those interface subnets from ; trying to send a STUN packet to find the external IP address. ; Attempting to send the STUN packet needlessly delays processing incoming ; and outgoing SIP INVITEs because we will wait for a response that can ; never come until we give up on the response. ; * Multiple subnets may be listed. ; * Blacklisting applies to IPv4 only. STUN isn't needed for IPv6. ; * Blacklisting applies when binding RTP to specific IP addresses and not ; the wildcard 0.0.0.0 address. e.g., A PJSIP endpoint binding RTP to a ; specific address using the bind_rtp_to_media_address and media_address ; options. Or the PJSIP endpoint specifies an explicit transport that binds ; to a specific IP address. ; ; e.g. stun_blacklist = 192.168.1.0/255.255.255.0 ; stun_blacklist = 10.32.77.0/255.255.255.0 ; ; stun_blacklist = ; ; Hostname or address for the TURN server to be used as a relay. The port ; number is optional. If omitted the default value of 3478 will be used. ; This option is disabled by default. ; ; e.g. turnaddr=myturn.server.com:34780 ; ; turnaddr= ; ; Username used to authenticate with TURN relay server. ; turnusername= ; ; Password used to authenticate with TURN relay server. ; turnpassword= ; ; Subnets to exclude from ICE host, srflx and relay discovery. This is useful ; to optimize the ICE process where a system has multiple host address ranges ; and/or physical interfaces and certain of them are not expected to be used ; for RTP. For example, VPNs and local interconnections may not be suitable or ; necessary for ICE. Multiple subnets may be listed. If left unconfigured, ; all discovered host addresses are used. ; ; e.g. ice_blacklist = 192.168.1.0/255.255.255.0 ; ice_blacklist = 10.32.77.0/255.255.255.0 ; ; ice_blacklist = ; [ice_host_candidates] ; ; When Asterisk is behind a static one-to-one NAT and ICE is in use, ICE will ; expose the server's internal IP address as one of the host candidates. ; Although using STUN (see the 'stunaddr' configuration option) will provide a ; publicly accessible IP, the internal IP will still be sent to the remote ; peer. To help hide the topology of your internal network, you can override ; the host candidates that Asterisk will send to the remote peer. ; ; IMPORTANT: Only use this functionality when your Asterisk server is behind a ; one-to-one NAT and you know what you're doing. If you do define anything ; here, you almost certainly will NOT want to specify 'stunaddr' or 'turnaddr' ; above. ; ; The format for these overrides is: ; ; => ; ; The following will replace 192.168.1.10 with 1.2.3.4 during ICE ; negotiation: ; ;192.168.1.10 => 1.2.3.4 ; ; You can define an override for more than 1 interface if you have a multihomed ; server. Any local interface that is not matched will be passed through ; unaltered. Both IPv4 and IPv6 addresses are supported.