| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138 |
- Kernel driver f71882fg
- ======================
- Supported chips:
- * Fintek F71808E
- Prefix: 'f71808e'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Not public
- * Fintek F71808A
- Prefix: 'f71808a'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Not public
- * Fintek F71858FG
- Prefix: 'f71858fg'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Available from the Fintek website
- * Fintek F71862FG and F71863FG
- Prefix: 'f71862fg'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Available from the Fintek website
- * Fintek F71869F and F71869E
- Prefix: 'f71869'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Available from the Fintek website
- * Fintek F71869A
- Prefix: 'f71869a'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Not public
- * Fintek F71882FG and F71883FG
- Prefix: 'f71882fg'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Available from the Fintek website
- * Fintek F71889FG
- Prefix: 'f71889fg'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Available from the Fintek website
- * Fintek F71889ED
- Prefix: 'f71889ed'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Should become available on the Fintek website soon
- * Fintek F71889A
- Prefix: 'f71889a'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Should become available on the Fintek website soon
- * Fintek F8000
- Prefix: 'f8000'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Not public
- * Fintek F81801U
- Prefix: 'f71889fg'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Not public
- Note: This is the 64-pin variant of the F71889FG, they have the
- same device ID and are fully compatible as far as hardware
- monitoring is concerned.
- * Fintek F81865F
- Prefix: 'f81865f'
- Addresses scanned: none, address read from Super I/O config space
- Datasheet: Available from the Fintek website
- Author: Hans de Goede <hdegoede@redhat.com>
- Description
- -----------
- Fintek F718xx/F8000 Super I/O chips include complete hardware monitoring
- capabilities. They can monitor up to 9 voltages, 4 fans and 3 temperature
- sensors.
- These chips also have fan controlling features, using either DC or PWM, in
- three different modes (one manual, two automatic).
- The driver assumes that no more than one chip is present, which seems
- reasonable.
- Monitoring
- ----------
- The Voltage, Fan and Temperature Monitoring uses the standard sysfs
- interface as documented in sysfs-interface, without any exceptions.
- Fan Control
- -----------
- Both PWM (pulse-width modulation) and DC fan speed control methods are
- supported. The right one to use depends on external circuitry on the
- motherboard, so the driver assumes that the BIOS set the method
- properly.
- Note that the lowest numbered temperature zone trip point corresponds to
- to the border between the highest and one but highest temperature zones, and
- vica versa. So the temperature zone trip points 1-4 (or 1-2) go from high temp
- to low temp! This is how things are implemented in the IC, and the driver
- mimicks this.
- There are 2 modes to specify the speed of the fan, PWM duty cycle (or DC
- voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM
- mode where the actual RPM of the fan (as measured) is controlled and the speed
- gets specified as 0-100% of the fan#_full_speed file.
- Since both modes work in a 0-100% (mapped to 0-255) scale, there isn't a
- whole lot of a difference when modifying fan control settings. The only
- important difference is that in RPM mode the 0-100% controls the fan speed
- between 0-100% of fan#_full_speed. It is assumed that if the BIOS programs
- RPM mode, it will also set fan#_full_speed properly, if it does not then
- fan control will not work properly, unless you set a sane fan#_full_speed
- value yourself.
- Switching between these modes requires re-initializing a whole bunch of
- registers, so the mode which the BIOS has set is kept. The mode is
- printed when loading the driver.
- Three different fan control modes are supported; the mode number is written
- to the pwm#_enable file. Note that not all modes are supported on all
- chips, and some modes may only be available in RPM / PWM mode.
- Writing an unsupported mode will result in an invalid parameter error.
- * 1: Manual mode
- You ask for a specific PWM duty cycle / DC voltage or a specific % of
- fan#_full_speed by writing to the pwm# file. This mode is only
- available on the F71858FG / F8000 if the fan channel is in RPM mode.
- * 2: Normal auto mode
- You can define a number of temperature/fan speed trip points, which % the
- fan should run at at this temp and which temp a fan should follow using the
- standard sysfs interface. The number and type of trip points is chip
- depended, see which files are available in sysfs.
- Fan/PWM channel 3 of the F8000 is always in this mode!
- * 3: Thermostat mode (Only available on the F8000 when in duty cycle mode)
- The fan speed is regulated to keep the temp the fan is mapped to between
- temp#_auto_point2_temp and temp#_auto_point3_temp.
- All of the automatic modes require that pwm1 corresponds to fan1, pwm2 to
- fan2 and pwm3 to fan3.
|
