tlan.txt 3.8 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117
  1. (C) 1997-1998 Caldera, Inc.
  2. (C) 1998 James Banks
  3. (C) 1999-2001 Torben Mathiasen <tmm@image.dk, torben.mathiasen@compaq.com>
  4. For driver information/updates visit http://www.compaq.com
  5. TLAN driver for Linux, version 1.14a
  6. README
  7. I. Supported Devices.
  8. Only PCI devices will work with this driver.
  9. Supported:
  10. Vendor ID Device ID Name
  11. 0e11 ae32 Compaq Netelligent 10/100 TX PCI UTP
  12. 0e11 ae34 Compaq Netelligent 10 T PCI UTP
  13. 0e11 ae35 Compaq Integrated NetFlex 3/P
  14. 0e11 ae40 Compaq Netelligent Dual 10/100 TX PCI UTP
  15. 0e11 ae43 Compaq Netelligent Integrated 10/100 TX UTP
  16. 0e11 b011 Compaq Netelligent 10/100 TX Embedded UTP
  17. 0e11 b012 Compaq Netelligent 10 T/2 PCI UTP/Coax
  18. 0e11 b030 Compaq Netelligent 10/100 TX UTP
  19. 0e11 f130 Compaq NetFlex 3/P
  20. 0e11 f150 Compaq NetFlex 3/P
  21. 108d 0012 Olicom OC-2325
  22. 108d 0013 Olicom OC-2183
  23. 108d 0014 Olicom OC-2326
  24. Caveats:
  25. I am not sure if 100BaseTX daughterboards (for those cards which
  26. support such things) will work. I haven't had any solid evidence
  27. either way.
  28. However, if a card supports 100BaseTx without requiring an add
  29. on daughterboard, it should work with 100BaseTx.
  30. The "Netelligent 10 T/2 PCI UTP/Coax" (b012) device is untested,
  31. but I do not expect any problems.
  32. II. Driver Options
  33. 1. You can append debug=x to the end of the insmod line to get
  34. debug messages, where x is a bit field where the bits mean
  35. the following:
  36. 0x01 Turn on general debugging messages.
  37. 0x02 Turn on receive debugging messages.
  38. 0x04 Turn on transmit debugging messages.
  39. 0x08 Turn on list debugging messages.
  40. 2. You can append aui=1 to the end of the insmod line to cause
  41. the adapter to use the AUI interface instead of the 10 Base T
  42. interface. This is also what to do if you want to use the BNC
  43. connector on a TLAN based device. (Setting this option on a
  44. device that does not have an AUI/BNC connector will probably
  45. cause it to not function correctly.)
  46. 3. You can set duplex=1 to force half duplex, and duplex=2 to
  47. force full duplex.
  48. 4. You can set speed=10 to force 10Mbs operation, and speed=100
  49. to force 100Mbs operation. (I'm not sure what will happen
  50. if a card which only supports 10Mbs is forced into 100Mbs
  51. mode.)
  52. 5. You have to use speed=X duplex=Y together now. If you just
  53. do "insmod tlan.o speed=100" the driver will do Auto-Neg.
  54. To force a 10Mbps Half-Duplex link do "insmod tlan.o speed=10
  55. duplex=1".
  56. 6. If the driver is built into the kernel, you can use the 3rd
  57. and 4th parameters to set aui and debug respectively. For
  58. example:
  59. ether=0,0,0x1,0x7,eth0
  60. This sets aui to 0x1 and debug to 0x7, assuming eth0 is a
  61. supported TLAN device.
  62. The bits in the third byte are assigned as follows:
  63. 0x01 = aui
  64. 0x02 = use half duplex
  65. 0x04 = use full duplex
  66. 0x08 = use 10BaseT
  67. 0x10 = use 100BaseTx
  68. You also need to set both speed and duplex settings when forcing
  69. speeds with kernel-parameters.
  70. ether=0,0,0x12,0,eth0 will force link to 100Mbps Half-Duplex.
  71. 7. If you have more than one tlan adapter in your system, you can
  72. use the above options on a per adapter basis. To force a 100Mbit/HD
  73. link with your eth1 adapter use:
  74. insmod tlan speed=0,100 duplex=0,1
  75. Now eth0 will use auto-neg and eth1 will be forced to 100Mbit/HD.
  76. Note that the tlan driver supports a maximum of 8 adapters.
  77. III. Things to try if you have problems.
  78. 1. Make sure your card's PCI id is among those listed in
  79. section I, above.
  80. 2. Make sure routing is correct.
  81. 3. Try forcing different speed/duplex settings
  82. There is also a tlan mailing list which you can join by sending "subscribe tlan"
  83. in the body of an email to majordomo@vuser.vu.union.edu.
  84. There is also a tlan website at http://www.compaq.com